Isolated DIN Rail Loop-Powered Temperature Signal Conditioner

DRSL-TEMP

Isolated DIN Rail loop-powered Signal Conditioner

^¥31,900 DRSL-TEMP

注文する

Type J or K Thermocouple or 2, 3 or 4-Wire Pt100 RTD Input
Powered By the Host (Output) Current Signal Loop
Slimline 6 mm (0.24") Housing
High Accuracy
Excellent EMC Performance and 50/60 Hz Noise Suppression
Fast Response Time <30 ms/300 ms (Selectable)
Pre-Calibrated Temperature Ranges Selectable via DIP-Switches

プロセス計測 / 制御機器 - 関連する商品を探す
（見つからない場合はカスタマーサービスにご連絡ください）

商品説明

The DRSL-TEMP isolated DIN rail loop-powered temperature signal conditioner measures a standard type J or K thermocouple or a 2-, 3- or 4-wire Pt100 RTD temperature sensor and provides a passive analog current output signal.

The DRSL-TEMP offers 2-way isolation between input and output, provides surge suppression and protects control systems from transients and noise.

The DRSL-TEMP provides a competitive choice in terms of both price and technology for interfacing thermocouple or RTD signals to SCADA systems or PLC equipment. This unit is powered by the host (output) current signal loop. Low power consumption facilitates DIN rail mounting without the need for any air gap. Easy configuration of more than 1000 factory calibrated measurement ranges is done via DIP-switches. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).

SPECIFICATIONS
INPUT
THERMOCOUPLE INPUT
Type: J or K thermocouple
Temperature Range (DIP Swich Selectable)
    Type J: -100 to 1200°C (-148 to 2192°F)
    Type K: -180 to 1372°C (-292 to 2501°F)
Sensor and Cable Specifications: 5 kΩ per wire
Cold Junction Compensation (CJC): Internal or external (selectable)
    CJC Accuracy via External CJC (Pt100 RTD Sensor): Better than ±0.15°C
    CJC via Internally Mounted Sensor: Better than ±2.5°C
Open Thermocouple Detection: Yes (DIP switch selectable upscale or downscale)
Pt100 RTD INPUT
Type: 2, 3, or 4-wire Pt100 RTD
Temperature Range (DIP Switch Selectable): -200 to 850°C (-328 to 1562°F)
Sensor Current, RTD: <150 µA
Sensor Cable Specifications: 50 Ω per wire
Effect of Sensor Cable Resistance (3 or 4-Wire RTD): <0.002 Ω/Ω
Broken Sensor Detection: >800 Ω
Shorted Sensor Detection: <18 Ω

OUTPUT
Current Output
    Programmable Signal Ranges: 0 to 20 mA and 4 to 20 mA
    Range Limits (NAMUR NE43 Out of Range): Below 3.8 mA or above 20.5 mA
    Sensor Error Detection (Dip Switch Selectable for Enable or None): Below 3.5 mA or above 23 mA
    Incorrect DIP-Switch Setting Identification: Below 3.5 mA
    Output Error Level: DIP switch selectable for upscale or downscale
    Load Resistance (Ω): ≤(Vsupply - 5.5)/0.023
    Load Stability: ≤0.01% of span/100 Ω

GENERAL
Supply Voltage: 5.5 to 35 Vdc
Voltage Drop: 5.5 Vdc
Isolation: Input/output
Isolation Voltage (Test): 2.5 kVac (reinforced)
Isolation Voltage (Working): 300 Vac
Signal/Noise Ratio: >60 dB
Response Time (0 to 90%, 100 to 10%): <30 ms/300 ms (selectable, provides either fast response or signal dampening as needed)
Accuracy
    Thermocouple Input: Better than 0.5°C or ±0.05% of span (selected input range)
    RTD Input: Better than 0.1°C or ±0.05% of span (selected input range)
Temperature Coefficient
    Thermocouple Input: ≤±0.1°C/°C or ≤±0.01%/°C
    RTD Input: ≤±0.02 °C/°C
EMC Immunity Influence: <±0.5% of span
Extended EMC Immunity
    NAMUR NE 21, A Criterion, Burst: <±1% of span (span = selected input range)

ENVIRONMENTAL
Operating Temperature: -25 to 70°C (-13 to 158°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Calibration Temperature: 20 to 28°C (68 to 82°F)
Relative Humidity: 0 to 95% RH non-condensing
Protection Degree: IP20
Installation Area: Pollution degree 2 and measurement/overvoltage category II

MECHANICAL
Dimensions: 113 H x 6.1 W x 115 mm D (4.4 x 0.24 x 4.5")
Weight: 70 g (0.15 lb) approx
DIN Rail Type: DIN EN 60715 - 35 mm
Wire Size: 0.13 x 2.5 mm²/AWG 26 to 12 stranded wire
Screw Terminal Torque: 0.5 Nm

注文する（部品番号ビルダーより掲載以外の製品もご選択いただけます）(注文数を入力の上、"カートに追加"をクリックしてください)

部品番号/Desc.

注文数

商品説明

DRSL-TEMP

¥35,090 (税込)
(税抜価格 ¥31,900)

納期: 6 週間

Isolated DIN rail loop-powered temperature signal conditioner

Accessories

RAIL-35-1

¥3,274 (税込)
(税抜価格 ¥2,976)

納期: 2 週間

35 mm (1.4") DIN rail, 1 m (3.3') length

DRSL-MOD-STOP

¥1,617 (税込)
(税抜価格 ¥1,470)

納期: 5 週間

Module stop (screwed onto DIN rail to support and hold mounted devices)

Ordering Example: (1) DRSL-MOD-STOP Module stop (screwed onto DIN rail to support and hold mounted devices), ¥1,470 plus (1) DRSL-TEMP Isolated DIN rail loop-powered temperature signal conditioner, ¥31,900 plus (1) RAIL-35-1 35 mm (1.4, ¥2,976, ¥1,470 + 31,900 + 2,976 = ¥36,346