End Suction Centrifugal Pumps - Discontinued

FPUC200 Series Discontinued

スクロールダウンし、全ラインアップをご覧ください

Easy Screwdriver Service
Chemical Resistant
Flows to 230 U.S. GPM or 94' TDH at 60 Hz (725 LPM or 20 m at 50 Hz)
Constructed from Glass-Reinforced Polyester or Noryl Thermoplastic

商品説明

The FPUC200 has been discontinued. Please contact our Flow and Environmental department for possible substitutes.

All major pump parts in the FPUC200 Series are precision molded of tough, corrosion-resistant glass-reinforced polyester or Noryl glass-reinforced thermoplastic. These high-strength plastics provide resistance to water and salt water as well as to many acids, bases and solvents. O-rings and seals are of EPDM, FKM, or Buna-N. They utilize 18-8 SS wetted internal hardware. For extra corrosive service, the motor shaft adaptor can be made of titanium, the impeller screw can be encapsulated in polypropylene, and the mechanical seals can be made metalless with FKM and siliconized graphite seal faces (add suffix “-TPV” to the model number and add $700 to price), or the mechanical seals can be made metalless with EPDM and siliconized graphite seal faces (add suffix “-TPM” and add $638 to price).

WARNING:
When pumping flammable or combustible liquids, all containers must be effectively bonded and grounded to prevent sparks of static electricity which could cause an explosion

Model No.	Max Flow Rate*		Max TDH		Motor HP 60 Hz	Max Spec. Grav.
Model No.	GPM	LPM	Ft.	M	Motor HP 60 Hz	Max Spec. Grav.
With Single-Phase, 115/230 VAC, TEFC Motor
FPUC201	70	220	30	6.5	0.75	1.8
FPUC202	90	285	32	7	1.5	1.6
FPUC203	120	380	70	15	2	1.1
With 3-Phase, 230/460 Vac, TEFC Motor
FPUC204	70	220	30	6.5	0.75	1.8
FPUC205	90	285	32	7	1.5	1.6
FPUC206	120	380	70	15	2	1.6
FPUC207	150	475	90	19	3	1

70 and 90 GPM units are 1750 RPM motors; all others are 3450 RPM

Model No.	Max Flow Rate*		Max TDH		Required HP
Model No.	GPM	LPM	Ft.	M	60 Hz	50 Hz
FPUC208	70	220	30	6.5	0.4	0.31
FPUC209	90	285	32	7	0.9	0.5
FPUC210	120	380	70	15	1.8	1
FPUC211	150	475	90	19	3	1.7
FPUC212	180	570	94	20	4.8	2.8
FPUC213	230	725	70	15	4.9	2.8

*GPM @ 1725 & 3450 RPM, 60 cycle motors: LPM @ 1450 & 2850 RPM, 50 cycle motors. For Noryl body instead of polyester, add suffix “-NL” to model numbers, and add $45 to price. For optional Buna-N or FKM elastomers, add suffix “-B” or “-V” to model number and add $138 for FKM, no charge for Buna-N. For 50 Hz motor, please specify ”-Voltage/Phase/50 Hz” (consult OMEGA'S Flow Engineering Department for price). To order an EDPM fitted hard siliconized graphite faced shaft seal for abrasive applications, add suffix “-SC” to model number and add $215 to price.

注文する（部品番号ビルダーより掲載以外の製品もご選択いただけます）(注文数を入力の上、"カートに追加"をクリックしてください)

部品番号/Desc.

注文数

商品説明

FPUC204

お問い合せ下さい

納期:

end suction centrifugal pump, 70 GPM