Constant Temperature Heated Dry Baths

HDB

スクロールダウンし、全ラインアップをご覧ください

注文する

Uniform Heating for Test Tubes, Cuvettes, and Other Sample Containers
Interchangeable Insert Blocks
Models for 1, 2 or 3 Insert Blocks
Solid State Temperature Control

温度校正器 / 実験用機器 - 関連する商品を探す
（見つからない場合はカスタマーサービスにご連絡ください）

商品説明

OMEGA™ HDB series heated dry baths provide a safe, dry, constant temperature source in the laboratory for the purpose of incubation, boiling, inactivation, wet ashing, enzyme analysis and a variety of clinical and industrial applications.

Interchangeable aluminum insert blocks are sized to accept tubes or containers ranging from 6 mm to 26 mm diameter. A close fit of the tubes in the block ensures high heat transfer to the tube, and the heater design, thermistor temperature sensor and solid state circuitry give exceptionally good temperature stability and uniformity.

Temperature stability is ±0.1°C, and uniformity between blocks is ± 0.2°C (both at 40°C).

Temperatures are adjusted in the HDB-1, HDB-2, and HDB-3 using a dial calibrated in degrees centigrade. On the HDB-3D, the dial and digital display are used to set the temperature. The digital indicator also provides a continuous temperature display.

A block extraction tool, and threaded fitting machined into the block, allow easy block removal. The threaded hole is also used to insert glass thermometers for accurate temperature measurement of the block.

Aluminum Insert Blocks

Model No.	Tube Size	Number of Holes	Size (mm)
6013501	Plain Block	None	95 x 76 x 51
6013502	6 mm	30	95 x 76 x 51
6013503	10 mm	20	95 x 76 x 51
6013504	12 mm	20	95 x 76 x 51
6013505	13 mm	20	95 x 76 x 51
6013506	15 mm	12	95 x 76 x 51
6013507	16 mm	12	95 x 76 x 51
6013508	19 mm	8	95 x 76 x 51
6013509	25 mm	6	95 x 76 x 51
6013510	10 mm cuvettes 2 channels		95 x 76 x 51
6013512*	Plain Block Thermometer	Hole Only	95 x 225 x 51
6014460	Plain Block Thermometer	Hole Only	95 x 76 x 51
6014462	24 mm	6	95 x 76 x 51
6014463	26 mm	6	95 x 76 x 51
6014464	1.5 ml Eppendorf	20	95 x 76 x 51
6014465	0.5 ml Eppendorf	30	95 x 76 x 51
6014466	Plastic Half Plain Blocks**		95 x 37 x 50

*For HDB-3, HDB-3D only
**If less than the maximum number of blocks are used, it is recommended that the plastic half blocks fill the space on either side of the aluminum block(s) in order to maintain temperature stability

注文する（部品番号ビルダーより掲載以外の製品もご選択いただけます）(注文数を入力の上、"カートに追加"をクリックしてください)

部品番号/Desc.

注文数

商品説明

Heated Dry Baths

HDB-2

お問い合せ下さい

納期:

Heated dry bath, 2 blocks, 25°C to 105°C, 450 W, 120V

HDB-3

お問い合せ下さい

納期:

Heated dry bath, 3 blocks, 25°C to 200°C 650 W, 120V

HDB-3D

お問い合せ下さい

納期:

Heated dry bath, 3 blocks, 25°C to 200°C 650 W, 120V, temperature and setpoint display

Aluminum Insert Blocks

6013501

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

0-hole insert block

6013502

お問い合せ下さい

納期:

30-hole insert block

6013503

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

20-hole insert block

6013504

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

20-hole insert block

6013505

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

20-hole insert block

6013506

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

12-hole insert block

6013507

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

12-hole insert block

6013508

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

8-hole insert block

6013509

¥57,189 (税込)
(税抜価格 ¥51,990)

納期: 16 週間

6-hole insert block

6013510

お問い合せ下さい

納期:

Insert block

6013512

¥152,928 (税込)
(税抜価格 ¥139,025)

納期: 16 週間

Hole-only insert block

6014460

お問い合せ下さい

納期:

Hole-only insert block

6014462

お問い合せ下さい

納期:

6-hole insert block

6014463

¥57,156 (税込)
(税抜価格 ¥51,960)

納期: 16 週間

6-hole insert block

6014464

お問い合せ下さい

納期:

20-hole insert block

6014465

お問い合せ下さい

納期:

30-hole insert block

6014466

¥16,159 (税込)
(税抜価格 ¥14,690)

納期: 16 週間

Insert block

注: Comes with block extraction tool, power cord and plug, and operator’s manual. Aluminum insert blocks are ordered separately (see table above).
240 volt models also available. To order add “-240V” suffix to model number.
Ordering Example: (2) 6013503 20-hole insert blocks, ¥51,9900