1/4" Diameter Probe Design for Standard Duty, or 3/8" to 3/16" Stepped Probe Design For Heavy Duty Applications
Probe Lengths of 3", 4", 5" and 6" Available From Stock, Other Lengths Also Available
Process Connection is a 1½"-16 AMP Tri-Grip™ (Tri-Clamp® Compatible) Standard, Other Sizes and Styles Available. Flanges Conform to ASME BPE-2007 Standard to Assure Trouble Free Interchangeability.
Sensor Can be Used in Sanitary, Hygienic and Clean-In-Place Food, Dairy, Beverage and BioPharmaceutical Processes
316L SS Wetted Surfaces with 32 µinch or Better Surface Finish
4-Conductor, 120" Long PFA Cable with Molded Nylon Strain Relief Standard
-50 to 200°C (-58 to 392°F) Temperature Range
4-Wire Pt100 Class A Platinum RTD Sensor (100.00±0.06Ω at 0°C) Standard
Compatible with 3-Wire and 2-Wire RTD Instruments and Transmitters
Sanitary Temperature Sensor Specifications Include:
316L stainless steel process wetted surfaces with surface finishes
of 32 microinches or better.
Probe lengths of 3, 4, 5 or 6 inches available from stock, other lengths available
as special orders.
Sensor Output is a 4-wire, 100 ohm, Class A, Platinum RTD meeting
the requirements of IEC 60751.
These sensors can be used with 2-wire or 3-wire systems see information below.
Insulation resistance: 100 megohms minimum at 100 VDC.
Thermal response time of less than 2.5 seconds in water flowing
at 3 ft/sec (63% response).
This Sanitary Temperature Sensor containes a PT100 Platinum RTD element and is designed for use in Food, Dairy, Beverage and BioPharmaceutical Clean-In-Place (CIP) type applications. The sensor includes a
1½" 16AMP process connection that conforms to ASME BPE-2007 for easy installation using industry standard
gaskets and clamps. Standard Duty sensors are available with ¼"
diameter probes, and Heavy Duty sensors are available with a stepped 3⁄8" to
3⁄16" diameter probe. This sensor is provided with a 120" long, 4-conductor, #26AWG
stranded nickel plated copper, PFA insulated and jacketed cable with
a strain relief for convenient connection to control or monitoring
equipment.
Food process hygienic temperature sensors can be used to aid food safety inspection compliance and verification of time temperature control. Combined with a chart recorder model CTXL you can temperature monitor a CCP ( Critical Control Point) or sanitation time and move toward a HACCP (Hazard Analysis Critical Control Point) compliance plan.
In addition to the standard 1½-16AMP process connection, these can be provided
in the following sizes and styles:
Process Connection
Model Number Code
3/4"-16AMP
-B1-
1" and 1½"-16AMP
-D1-
2"-16AMP
-E1-
2½"-16AMP
-F1-
3"-16AMP
-G1-
4"-16AMP
-H1-
If you need a process connection that is not listed above, please contact our sales department for availability.
These sanitary sensors are supplied standard as 4-wire assemblies with two
red wires and two white wires. When used in 3-wire applications,
cut off one white wire making sure that it will not contact any terminals
or metal surfaces (note: twisting the two white wires together will reduce
the lead wire resistance on one side of the sensing element by half
adversely affecting the accuracy of the reading).
When used in 2-wire applications, cut off one white wire
and one red wire (note: in 2-wire applications, twisting the two
same-colored wires together at the terminals will not adversely
affect your sensor accuracy since both wires will be affected by
the reduction in resistance).
These sensors are also
available in Thermistor
and Thermocouple styles to accommodate any process input requirement.
クイックオーダー
注:
For standard duty probe lengths longer than 6", change "-0600" in model number to the required length (example: 12" = "-1200", 9¼" = "-0925") and add $1 per inch to the price (up to 24 inches).
For heavy duty probe lengths longer than 6", change "-0600" in model number to the required length (example: 12" = "-1200", 9¼" = "-0925") and add $2.50 per inch to the price (up to 24 inches).
For other than the standard 1½-16AMP process connection, change "-D1-" in the model number to the code for the alternate process connection option listed above the "To Order" table and add $20 to the price
For cable lengths longer than 10' (120"), change the "-120" in model number to the desired length in inches and add $1 per foot to the price.
For probe lengths longer than 24 inches please contact Customer Service.
Ordering Example: (1) PRS-3-100-A-S-0400-D1-CB-120 Sanitary RTD sensor with 4-wire Pt100, Class A accuracy element, ¼'' diameter probe 4'' long with 1½'', 16AMP mounting cap and integral 120 inch long, 4-conductor cable with strain relief, ¥56,080
部品番号ビルダー
下記から仕様構成を選択し、ご注文ください
以下からオプションを選択:
(1)
Nominal Element Resistance : 100 : 100 ohm @ 0 C (standard) 1000 : 1 kohm @ 0 C
(2)
Accuracy : A : Class A Accuracy
(3)
Probe Diameter : S : Standard Duty 1/4 inch H : Heavy Duty 3/8 to 3/16 inch stepped probe
(4)
Probe Length : 0300 : 3 inch length 0400 : 4 inch length 0500 : 5 inch length 0600 : 6 inch length
(5)
Sanitary Flange (Cap) Size : D1 : 1-1/2 inch Tri-Grip Flange (standard) B1 : 3/4 inch 16AMP Tri-Grip Flange E1 : 2 inch 16AMP Tri-Grip Flange F1 : 2-1/2 inch 16AMP Tri-Grip Flange G1 : 3 inch 16AMP Tri-Grip Flange H1 : 4 inch 16AMP Tri-Grip Flange
(6)
Lead Wire Cable Length : 120 : 120 inch/10 ft (standard) 144 : 144 inch/12 ft 180 : 180 inch/15 ft 240 : 240 inch/20 ft
Temperature Controllers Product Finder - It's the easiest way to sort through our selection of temperature controllers to find the right product for your application
Data Acquisition Product Finder - It's the easiest way to sort through our selection of data acquisition systems to find the right product for your application
We noticed you are from the US. Visit your local site for regional offers and live support.
